Logo

P0352 Engine Trouble Code

P0352 Engine

When you check engine light came on code P0352 the reason should be Engine Light ON (or Service Engine Soon Warning Light). However your vehicle's manufacturer may have a different definition for the P0352 OBD-II Diagnostic Powertrain (P) Trouble Code. So you should chech it on our car models.

When the DTC check engine light comes P0352 code on the first you can check is the gas related maybe gas cap. Pull over, retighten it, and take a look at the cap to see if it has any cracks inside. Go on driving and to see if the check engine light turns off automaticly. On the other hand, you can buy a gas cap for about $4.5 at an auto parts store. All you need to do is take the old one take off and take on the new one. If you've already bought it to the store, you might as well just replace the cap. While not car-threatening, it's good to take care of this right away to improve gas mileage/km.

P0352 Code Meaning :

P
OBD-II Diagnostic Powertrain (P) Trouble Code For Engine
0
Intake Valve Control Solenoid Circuit Low
3
Fuel Rail Pressure Sensor Circuit Malfunction
5
Turbocharger Boost Sensor A Circuit Low
2
Crankshaft Position Sensor A Circuit Low Input

The oxygen (02) sensors on your car measure the oxygen in the exhaust to determine how rich or lean the ratio of fuel and air are in the cylinders. Optimizing this mixture means better fuel economy and fewer exhaust emissions.

P0352 OBD-II Diagnostic Powertrain (P) Trouble Code Description

P0352 OBD-II Trouble Code The ignition system on the vehicle uses individual ignition coils for each cylinder. The Engine Control Module ( P0352 code. Fuel Rail Pressure Sensor Circuit Malfunction and Turbocharger Boost Sensor A Circuit Low causes most of code P0352.

Reason For P0352 Code

The reason of P0352 OBD-II Engine Trouble Code is Fuel Rail Pressure Sensor Circuit Malfunction.

Your car parts or components should not be replaced with reference to only a P0352 DTC. The vehicle service manual should be consulted for more information on possible causes of the error code, along with required testing.

How To Repair P0352 Code

Before starting let's see P0352 repairing process steps:

  • Qualified technicians will begin by using a scan tool to access P0352 code stored in the ECU.
  • Technicians will note P0352 code present and any freeze frame data associated with them.
  • After all, if you sure the engine trouble is finished, the code will be cleared.

A bad fuel pressure regulator can result in an accumulation of too much gasoline/diesel that causes your engine to backfire or the fuel to smell when you slow down your vehicle. If you see even a slight problem, it is essential to have it inspected to quickly correct any issues before any damage is further imposed on your car.

If nothing is done to repair the persistent P0352 code, the ECU will put the vehicle into a limp mode. This mode limits the top speed and reduces engine power greatly to protect the engine.

Sometimes P0352 code comes with P035200 code.

Diagnosis Of Engine Error OBD Code P0352

It's essential to diagnose this trouble code. Then are some way which a handyperson should follow for diagnosing the problem that started a P0352 trouble code to be stored

The first step is introductory and is about reacquiring all the canons that have been set. For this, the individual scanner will have to be plugged into the individual harborage of your vehicle. Make sure you indurate frame the data. Any canons that were set previous to the P0352 code will have to be sorted first, as they may have been the reason for the law to set in the first place. It's always good to rule that out.

The coming step is to run a introductory examination of all the electrical circuits, connectors, wiring etc for damages similar as becks, erosion, fraudulent legs etc. All of these will have to be repaired or replaced. After that's sorted, clear the canons and go on a test drive to see if it resets. In case it resets, you'll have to continue your opinion. Depending on your vehicle you may have a vacuum operated selector or a vacuum solenoid if it's electrically actuated. In the case of the former, a hand held vacuum pump will have to be used to testit.The purpose is to see if the internal stopcock is getting turned by the selector, motor or solenoid. In order to do this, a command can be transferred to the system with scanner or by driving the vehicle under the special conditions that will spark the system. While this is passing keep an eye on the checkup tool data for the result.

All Engine Trouble Codes

All engine trouble codes with P, U, B and C engine codes.

Code Search

Please fill the "Code Box" to find engine fault code.

Example: 0140

Car Models :

Please select your car.

How To Read Engine Codes ?

Ways to read engine trouble codes.

How To Clear Check Engine Lights ?

Ways to clear check engine light on car panel.

Check Engine Light Dictionary

Ways to clear check engine light on car panel.